--- doc/build/Attic/loncapasqldatabase.html	2001/02/12 17:38:13	1.6
+++ doc/build/Attic/loncapasqldatabase.html	2001/02/14 14:33:35	1.8
@@ -20,6 +20,7 @@ and a SQL database.
 <LI>Current status of documentation</LI>
 <LI>Current status of implementation</LI>
 <LI>Purpose within LON-CAPA</LI>
+<LI>Dependencies</LI>
 <LI>Installation</LI>
 <LI>Installation from source</LI>
 <LI>Configuration (automated)</LI>
@@ -55,7 +56,8 @@ Right now, a lot of "feasibility" work h
 Recipes for manual installation and configuration have
 been gathered.  Network connectivity of lond->lonsql->lond->lonc
 type tests have been performed.  A binary installation
-has been compiled in an RPM (LON-CAPA-mysql).
+has been compiled in an RPM (LON-CAPA-mysql, with perl components
+a part of LON-CAPA-systemperl).
 The most lacking test in terms of feasibility has
 been looking at benchmarks to analyze the load at which
 the SQL database can efficiently allow many users to
@@ -141,13 +143,33 @@ THE SOLUTION:
   processes (lonsql's) handle the MySQL database manipulations.
 </PRE>
 </P>
+<H2>Dependencies</H2>
+<P>
+I believe (but am not 100% confident) that the following
+RPMs are necessary (in addition to the current ones
+in rpm_list.txt) to run MySQL.  Basically I discovered these
+dependencies while trying to do external RPM based installs.
+I assume, and sometimes found, that these dependencies apply
+to tarball-based distributions too.  (So to play it on the
+safe side, I am going to include these RPMs as part of the
+core, minimal RPM set.)
+<UL>
+<LI>egcs-1.1.2-30</LI>
+<LI>cpp-1.1.2-30</LI>
+<LI>glibc-devel-2.1.3-15</LI>
+<LI>glibc-devel-2.1.3-15</LI>
+<LI>zlib-devel-1.1.3-6</LI>
+</UL>
+
+</P>
 <H2>Installation</H2>
 <P>
 Installation of the LON-CAPA SQL database normally occurs
 by default when using the LON-CAPA installation CD
 (see http://install.lon-capa.org).  It is installed
 as the LON-CAPA-mysql RPM.  This RPM encodes for the MySQL
-engine and related perl interfaces (Perl::DBI, Perl::Msql-Mysql).
+engine.  Related perl interfaces (Perl::DBI, Perl::Msql-Mysql)
+are encoded in the LON-CAPA-systemperl RPM.
 </P>
 <P>
 The three components of a MySQL installation for the
@@ -172,6 +194,30 @@ actual MySQL functionality on the system
 </P>
 <H2>Installation from source</H2>
 <P>
+Note: the mysql site recommends that Linux users install by
+using the MySQL RPMs (MySQL-client, MySQL, MySQL-shared, etc).
+While these RPMs work, I was unsuccessful at integrating
+this RPM-installed database with perl modules from www.cpan.org.
+Hence, I <STRONG>strongly</STRONG> recommend that, when installing
+from "source", MySQL and the perl components be in fact installed
+from their tarballs (.tar.gz, .tgz).  (Perl components, when installed
+from RPMs, also wound up in incorrect locations on the disk.)
+Do not coordinate a source install with externally made RPMs!
+It is, of course, okay to use LON-CAPA RPMs such as LON-CAPA-systemperl
+and LON-CAPA-mysql since we, in fact, made these RPMs correctly :).
+<UL>
+<LI>http://www.cpan.org/authors/id/JWIED/Msql-Mysql-modules-1.2215.tar.gz
+<BR>This tarball Released 20th August 2000
+<LI>http://www.mysql.com/Downloads/MySQL-3.23/mysql-3.23.33-pc-linux-gnu-i686.tar.gz
+<BR>This tarball Last changed 2000-11-11
+<BR>This is actually a binary tarball (as opposed to source code
+that is subsequently compiled).
+<LI>
+<BR>
+</UL>
+</P>
+<FONT COLOR="green"> old notes in green
+<P>
 The following set of tarballs was found to work together
 properly on a LON-CAPA RedHat 6.2 system:
 <UL>
@@ -184,6 +230,7 @@ properly on a LON-CAPA RedHat 6.2 system
 Installation was simply a matter of following the instructions
 and typing the several "make" commands for each 
 </P>
+</FONT>
 <H2>Configuration (automated)</H2>
 <P>
 Not yet developed.  This will be part of an interface