--- doc/build/suse9.2_install.frag	2005/07/31 21:19:23	1.1
+++ doc/build/suse9.2_install.frag	2005/08/27 21:16:20	1.3
@@ -1,4 +1,4 @@
-<h1>Installing LON-CAPA on a minimal SuSE 9.2 Linux Preofessional System</h1>
+<h1>Installing LON-CAPA on a minimal SuSE 9.2 Linux Professional System</h1>
 <p>
 This document guides you through the process of setting up a new LON-CAPA
 server running SuSE Linux Professional 9.2 (SLP 9.2) with a minimum of packages installed.  
@@ -24,7 +24,7 @@ perl, and MySQL are not required to inst
 The installation process takes the following steps:
 </p>
 <ol>
-  <li> Obtain SLP 9.2 installation media (DVD, CDs or mini-installation CD</li>
+  <li> Obtain SLP 9.2 installation media (DVD, CDs or mini-installation CD)</li>
   <li> Determine Network Settings</li>
   <li> Install SLP 9.2</li>
   <li> Update your system </li>
@@ -59,8 +59,8 @@ Installing SuSE Linux Professional is qu
 before.  Some documentation is available from 
 <a href="ttp://www.novell.com/documentation/suse92/">
 http://www.novell.com/documentation/suse92/</a>.<br /><br />
-If booting from a mini installation CD, use F3 to select TP or HTTP, and provide the IP address of a SuSE 9.2 mirror and a path to the 9.2 directory (e.g., 204.152.191.7  and suse/i386/9.2/), and enter the network information in the boot configuration (e.g., hostip=IPADDRESS netmask=NETMASK gateway=GATEWAY, replacing IPADDRESS, NETMASK and GATEWAY with appropriate values for your server.<br /><br />     
-Most of the subsequent installation screens are self explanatory.  
+If booting from a mini installation CD, use F3 to select FTP or HTTP, and provide the IP address of a SuSE 9.2 mirror and a path to the 9.2 directory (e.g., 204.152.191.7  and suse/i386/9.2/), and enter the network information in the boot configuration (e.g., hostip=IPADDRESS netmask=NETMASK gateway=GATEWAY), replacing IPADDRESS, NETMASK and GATEWAY with appropriate values for your server.<br /><br />     
+Most of the subsequent installation screens are self explanatory.
 There are a few steps that require comment and are dealt with below.
 </p>
 <dl style="list-style:square outside none">
@@ -96,7 +96,7 @@ There are a few steps that require comme
        IP address.  When configuring your network card, you should include host name information (e.g., host name = tmp1, domain = lite.msu.edu), as well as name server. Other settings (ip address, gateway, netmask will have been set when you included them in the boot configuration).
    </dd>
    <dt>Online update</dt>
-   <dd>Indicate "Yes" when prompted to "run online update now?</dd>
+   <dd>Indicate "Yes" when prompted to "run online update now?"</dd>
    </dt>
 </dl>
 <p>
@@ -116,14 +116,18 @@ Select "Change Source of Installation" a
 </p>
 <h3>Add an additional installation source</h3>
 <p>Add the LON-CAPA SuSE 9.2 repository as an additional installation source, so software installation in yast will have access to two repositories - a SuSE mirror (for packages included for the standard distribution) and the LON-CAPA repository (for extra packages needed to run LON-CAPA). For the LON-CAPA source you will use:
+<dl style="list-style:square outside none">
 <dd>Protocol</dd>
 <dt>HTTP</dt>
 <dd>Server Name</dd>
 <dt>install.loncapa.org</dt>
-<dd>Directory on server</dd>
-<dt>suse/9.2</dt>
+<dd>Directory on server (for 32 bit)</dd>
+<dt>suse/i386/9.2</dt>
+<dd>Directory on server (for 64 bit)</dd>
+<dt>suse/x86_64/9.2</dt>
 <dd>Authentication</dd>
 <dt>Anonymous</dt>
+</dl>
 After saving this configuration information for the LON-CAPA repository, choose "Edit", then "Refresh" the quit yast.    
 </p>
 <h2>Update pwdutils package</h2>
@@ -139,10 +143,16 @@ This may take a moment due to LON-CAPA's
 </p>
 <h3>Retrieve and execute LON-CAPA setup program</h3>
 <p>
-Retrieve the LON-CAPA setup with the following command:
+Retrieve the LON-CAPA setup with one of the following commands:
 </p>
+<i>32 bit architecture</i>
+<pre>
+wget http://install.loncapa.org/versions/suse/9.2/i386/suse_install.tar
+</pre>
+<br />
+<i>64 bit architecture</i>
 <pre>
-wget http://install.loncapa.org/versions/suse/9.2/suse_install.tar
+wget http://install.loncapa.org/versions/suse/9.2/x86_64/suse_install.tar
 </pre>
 <p>
 Extract the archive with the following command:
@@ -218,6 +228,7 @@ appropriate user name and your domain.
 cd /root/loncapa-N.N/loncom/build
 perl make_domain_coordinator.pl USERNAME DOMAIN
 (WILL PROMPT FOR PASSWORD HERE)
+mkdir ~USERNAME
 mkdir ~USERNAME/public_html
 chown USERNAME:www ~USERNAME/public_html
 chmod 0775 ~USERNAME/public_html
@@ -236,7 +247,7 @@ will be appearant at this step.
 If you receive warnings when starting the httpd about missing perl modules,
 please make sure you followed the instructions in 
 <b>Installing LON-CAPA Dependencies</b>.  If you still have errors, please
-contact the LON-CAPA development team.
+contact the LON-CAPA support team.
 </p>
 <h2>Log in to your LON-CAPA Machine</h2>
 <p>